← Back to ElectroLab
Electronics & RFIEC 60050-131 • IEEE 100 • AC Circuits

Inductive Reactance (X_L)

Enter L and frequency (or solve for either) to get reactance, impedance, phase and current.

XL = 2π f L  •  |Z| = √(R² + XL²)  •  θ = atan(XL/R)
Calculated Result
—

Step-by-step

  1. Enter valid values to begin.

Ideal inductance in series with a constant resistance R, sinusoidal steady state, rms values. The series model ignores core saturation, skin effect, core loss and winding capacitance, so it is valid well below the self-resonant frequency. Only the fields needed for the chosen mode are validated. If V is 0, current and power are skipped. The Q factor shown is XL/R of this series model.

IEC 60050-131 • IEEE 100 • IEC 60076-6 • IEC 62024-1 • AC Circuits

Inductive Reactance: Opposition That Grows With Frequency

Core Engineering Principles

Resistance burns power; reactance stores it and hands it back every cycle. An inductor resists a change in current, so the faster the current tries to swing, the harder it pushes back, and XL = 2πfL rises in a straight line with frequency. At DC the coil is just its wire. At 1 kHz a 10 mH choke is already 63 Ω. We never add reactance and resistance directly, because they sit 90° apart: |Z| = √(R² + XL²), with a phase angle of atan(XL/R).

This one relation is behind line reactors that tame drive harmonics, chokes that block switching noise, ballasts that limit lamp current without dissipating it, and the L in every LC filter. But the formula describes an ideal part, and real coils stop obeying it. Skin effect raises resistance at high frequency, and winding capacitance forms a self-resonant frequency (SRF). Above SRF the part looks capacitive and your “choke” passes the noise you meant to block. We stay well under SRF and under the saturation current, because a saturated core collapses L and reactance falls with it.

XL = 2πfL = ωL  •  L = XL / (2πf)  •  f = XL / (2πL)
|Z| = √(R² + XL²)  •  θ = atan(XL/R)  •  I = V / |Z|
Q (var) = I² XL  •  Q factor = XL / R

NEC & Standard References

IEC 60050-131 (International Electrotechnical Vocabulary, circuit theory) defines reactance, impedance and phase angle, and IEEE 100 gives the matching dictionary entries. IEC 60076-6 covers reactors used in power systems, including their rating and loss. IEC 62024-1 specifies high-frequency inductors for electronics, including inductance, rated current and self-resonant frequency measurement. These documents define terms and tests; the datasheet sets the limits. Check the adopted edition.
Worked Example: 10 mH Choke at 1 kHz
Given: L = 10 mH, f = 1 kHz, series resistance R = 5 Ω, applied V = 120 V.
1. ω = 2π × 1000 = 6283.2 rad/s, so XL = 6283.2 × 0.010 = 62.83 Ω.
2. |Z| = √(5² + 62.83²) = 63.03 Ω.
3. θ = atan(62.83 / 5) = 85.45°, nearly pure inductive.
4. I = 120 / 63.03 = 1.904 A.
5. Voltage across L = 1.904 × 62.83 = 119.6 V; across R = 9.52 V.
6. Reactive power Q = 1.904² × 62.83 = 227.7 var; Q factor = 62.83 / 5 = 12.57.
Real power is only 18.1 W, which is the winding heat.
Safety & Installation Rules
  • Don’t trust L above SRF. Past self-resonance the part is a capacitor, so read the impedance curve.
  • Remember ESR heating. Reactance does not dissipate power, but the series resistance does; I²R can run a choke hot even when the volt-amperes look modest.
  • Respect DC saturation. Bias or fault current beyond the rated saturation current drops L sharply, so reactance collapses and current spikes.
  • Never mix ω and f. Putting ω = 2πf into a formula that already contains 2π gives an answer 6.28 times too large.
  • Allow for tolerance. Inductors are commonly ±10% to ±20%, and XL moves by the same amount, so design for the worst case.

Reactance of Common Inductors

Reactance grows in a straight line with both frequency and inductance. The table gives the numbers you most often need at mains and signal frequencies.

XL = 2πfL. Real coils also add winding resistance, which this table ignores.
L50 Hz60 Hz1 kHz100 kHz1 MHz
1 µH0.314 mΩ0.377 mΩ0.00628 Ω0.628 Ω6.283 Ω
10 µH0.00314 Ω0.00377 Ω0.0628 Ω6.283 Ω62.83 Ω
100 µH0.0314 Ω0.0377 Ω0.628 Ω62.83 Ω628.3 Ω
1 mH0.314 Ω0.377 Ω6.283 Ω628.3 Ω6.283 kΩ
10 mH3.142 Ω3.77 Ω62.83 Ω6.283 kΩ62.83 kΩ
100 mH31.42 Ω37.7 Ω628.3 Ω62.83 kΩ628.3 kΩ
1 H314.2 Ω377 Ω6.283 kΩ628.3 kΩ6.283 MΩ

How Much Inductance Gives a Target Reactance?

This is the design direction for chokes, filters and ballasts. Choose the frequency you care about, then read off the inductance.

Inductance needed for a target reactance: L = XL / (2πf).
Target XL50 Hz60 Hz1 kHz100 kHz1 MHz
1 Ω3.18 mH2.65 mH159 µH1.59 µH159 nH
10 Ω31.8 mH26.5 mH1.59 mH15.9 µH1.59 µH
50 Ω159 mH133 mH7.96 mH79.6 µH7.96 µH
100 Ω318 mH265 mH15.9 mH159 µH15.9 µH
1000 Ω3.18 H2.65 H159 mH1.59 mH159 µH

Series R and L: Impedance and Phase

Resistance and reactance combine at right angles. When XL is ten times R the angle is already 84.3°, so the part acts as nearly pure inductance.

Series R = 10 Ω with increasing reactance.
XL|Z|Phase angleQ = XL/R
1 Ω10.05 Ω5.7°0.10
5 Ω11.18 Ω26.6°0.50
10 Ω14.14 Ω45.0°1.00
50 Ω50.99 Ω78.7°5.00
100 Ω100.50 Ω84.3°10.00

Worked Example: 3% Line Reactor on a 480 V Drive

A 30 A drive on a 480 V line. A 3% reactor means X = 0.03 × 480 / (√3 × 30) = 0.2771 Ω per phase. At 60 Hz, L = X / (2πf) = 0.2771 / 376.99 = 0.735 mH. That is the inductance you ask the manufacturer for, rated for at least 30 A continuous. The same reactor has about 0.231 Ω at 50 Hz.

Inductive Reactance Questions

What is the formula for inductive reactance?

XL = 2πfL, in ohms, with f in hertz and L in henries.

Why does reactance rise with frequency?

The coil resists change in current. The faster the current changes, the larger the opposing voltage, so the opposition grows in proportion to frequency.

What is the difference between reactance and impedance?

Reactance is the purely inductive part. Impedance combines it with resistance as |Z| = √(R² + XL²).

Does a coil dissipate power from its reactance?

Ideally no. The energy is stored and returned each cycle. Only the winding resistance dissipates real power.

Why does my choke stop working at high frequency?

Winding capacitance gives a self-resonant frequency. Above it the part behaves as a capacitor. Choose a choke whose SRF is well above your frequency.

Is reactance the same at 50 Hz and 60 Hz?

No. The same coil has 20% more reactance at 60 Hz than at 50 Hz, so current is lower on a 60 Hz supply.