← Back to ElectroLab
Electronics & RFNE555 Datasheet • IEC 60063

555 Timer Monostable Calculator

Enter R and C for the pulse width, or enter a target time and capacitor to get a standard resistor.

T = 1.1 × R × C  •  R = T / (1.1 C)  •  Trigger < VCC/3
Calculated Result
—

Step-by-step

  1. Enter valid values to begin.

Model: ideal one-shot with the threshold at 2/3 VCC, T = ln(3) × R × C = 1.1 RC. The trigger input must fall below 1/3 VCC and return high before the timing interval ends, otherwise the output stays high until the trigger is released. The initial error of about 1%, 50 ppm/°C and 0.1%/V figures are typical bipolar NE555-class datasheet values, the 200 mA output rating is the typical bipolar limit (CMOS parts source and sink much less), and the 10 MΩ resistor ceiling, 5-time-constant recovery and 50 Ω discharge-transistor resistance are engineering estimates, not guaranteed limits. Check the datasheet of your exact part. E12 values are from the IEC 60063 series.

NE555 / LM555 Datasheet • TLC555 / LMC555 • IEC 60063 E-Series

555 Monostable Timing: One Resistor, One Capacitor, One Pulse

Core Engineering Principles

In the one-shot configuration a falling trigger below one third of VCC sets the output high and releases the capacitor. It charges through a single resistor toward the supply and the comparator ends the pulse at two thirds. Charging from 0 to 2/3 of the final value takes ln 3 = 1.0986 time constants, which we round to 1.1. VCC cancels again, so the pulse width moves only about 0.1% per volt of supply change.

The trigger rules cause most of the field failures. The trigger must go low, below VCC/3, and then return high before the pulse ends. If it stays low longer than T, the output stays high until it is released, and your pulse width is whatever the trigger is. A trigger during the interval is ignored, and one right after it can arrive before the capacitor has discharged, giving a short pulse. For delays of minutes, remember that an electrolytic’s leakage current fights the timing resistor: use film capacitors at a few microfarads and resistors below about 10 MΩ, or let a counter divide a faster 555.

T = 1.1 × R × C  •  R = T / (1.1 × C)
Trigger < VCC / 3, pulse width < T  •  Spread = tolR + tolC + IC error

NEC & Standard References

The NE555 / LM555 datasheets from TI and ST give T = 1.1 R C, the trigger threshold of one third of VCC, a typical initial timing error of about 1% and a drift near 50 ppm/°C, plus an output rating of about 200 mA for the bipolar part. TLC555 and LMC555 are the CMOS equivalents with much lower supply current and lower output drive. IEC 60063 provides the E12 preferred values used to round R, and IEC 60384-1 is the generic fixed-capacitor specification covering tolerance and leakage classes. Confirm figures against the exact part’s datasheet.

Worked Example: 1.1 Second Relay Delay
Given: NE555 on 12 V, R = 100 kΩ, C = 10 µF film, R tolerance 1%, C tolerance 10%, trigger pulse 10 ms at 1 V, load 20 mA.
1. T = 1.1 × 100 kΩ × 10 µF = 1.100 s.
2. Worst-case spread = 1% + 10% + 1% = 12%, so T is 0.968 s to 1.232 s.
3. Trigger threshold = 12 / 3 = 4.00 V; 1 V is safely below it and the 10 ms pulse is far shorter than T.
4. Recovery ≈ 5 × 50 Ω × 10 µF = 2.5 ms, so the maximum trigger rate is about 0.907 Hz.
5. The 20 mA load is well within the 200 mA output rating.
Safety & Installation Rules
  • Keep the trigger short. A switch held for longer than T makes the output follow the switch, so condition it with a differentiating RC network.
  • Watch the output current. The bipolar output is rated to about 200 mA, but the high level droops under load; a CMOS 555 cannot drive a relay coil without a transistor.
  • Add a flyback diode. A relay coil on the output generates spikes that can destroy the timer.
  • Electrolytics stretch timing. Leakage steals charging current, so intervals longer than a few minutes need film capacitors or a counter.

Pulse Width for Common R and C

The one-shot gives T = 1.1 × R × C. The table is a quick look-up for standard parts, useful before you reach for the calculator above.

Pulse width T = 1.1 × R × C, ideal parts, no tolerance.
R0.01 µF0.1 µF1 µF10 µF100 µF
1 kΩ11 µs110 µs1.1 ms11 ms110 ms
4.7 kΩ51.7 µs517 µs5.17 ms51.7 ms517 ms
10 kΩ110 µs1.1 ms11 ms110 ms1.1 s
47 kΩ517 µs5.17 ms51.7 ms517 ms5.17 s
100 kΩ1.1 ms11 ms110 ms1.1 s11 s
470 kΩ5.17 ms51.7 ms517 ms5.17 s51.7 s
1 MΩ11 ms110 ms1.1 s11 s110 s

Which Resistor for a Target Delay?

Going the other way, pick the capacitor first and then round R to the E12 series. The second value in each cell is the pulse you really get, so you can see the rounding error at once.

Nearest E12 resistor and the pulse it actually gives. Practical range here is 1 kΩ to 5 MΩ.
Target TC = 0.1 µFC = 1 µFC = 10 µF
1 ms10 kΩ → 1.1 ms1 kΩ → 1.1 msout of range
10 ms100 kΩ → 11 ms10 kΩ → 11 ms1 kΩ → 11 ms
100 ms1 MΩ → 110 ms100 kΩ → 110 ms10 kΩ → 110 ms
1 sout of range1 MΩ → 1.1 s100 kΩ → 1.1 s
5 sout of range4.7 MΩ → 5.17 s470 kΩ → 5.17 s
10 sout of rangeout of range1 MΩ → 11 s

Long delays push R above a few megohms, where input bias and leakage start to matter. At that point use a larger film capacitor, or divide a faster 555 with a counter.

Worked Example: 5 Second Timer from 100 µF

Choose C = 100 µF. Then R = 5 / (1.1 × 100 µF) = 45.45 kΩ. The nearest E12 value is 47 kΩ, which gives T = 1.1 × 47 kΩ × 100 µF = 5.17 s. An electrolytic of this size can be 20% off and leaks, so expect anything from about 4.1 s to 6.2 s. For a tighter delay, use 10 µF film and a 470 kΩ resistor, or trim with a potentiometer in series with a 39 kΩ fixed resistor.

Troubleshooting a Monostable

Typical one-shot problems and where they come from.
SymptomLikely causeFix
Output stays high long after TTrigger held low longer than the pulseDifferentiate the trigger with a small capacitor and resistor so only the falling edge reaches pin 2
Pulse shorter than calculatedRetrigger before C has discharged, or leaky capacitorAllow recovery time; use film or low-leakage C and keep R below about 5 MΩ
Random pulses at power-upNoise on pin 2 below VCC/3Add a pull-up on trigger and a 10 nF capacitor on pin 5
Pulse width drifts with temperatureCapacitor tempco, not the ICUse C0G ceramic or film capacitors, not electrolytic or Y5V
Never triggersTrigger never goes below VCC/3 (4 V at 12 V)Check the drive level; a 1 V low is fine, a 5 V low is not

555 Monostable Questions

What is the formula for a 555 monostable pulse?

T = 1.1 × R × C. The capacitor charges from 0 to two thirds of VCC, which takes ln 3 = 1.0986 time constants, rounded to 1.1.

Does the supply voltage change the pulse width?

Very little. The timing thresholds are fractions of VCC, so the supply cancels. Datasheets show roughly 0.1% change per volt for the bipolar part.

Why does my output stay high when I hold the button?

If the trigger stays below VCC/3 when the pulse ends, the output cannot go low. Shape the trigger as a short pulse with a series capacitor and a pull-up resistor.

What is the longest practical delay?

With a film capacitor and about 5 MΩ you reach a few minutes. For hours, count the output of an astable 555 or use a microcontroller or RTC instead.

Can I use an electrolytic capacitor for timing?

Yes for rough delays, but leakage and wide tolerance change the pulse by tens of percent. Use film or C0G parts when accuracy matters.

How accurate is the result?

Add the resistor tolerance, the capacitor tolerance and about 1% for the IC. With 1% and 10% parts the total is near 12%, as in the worked example above.