← Back to ElectroLab
Electronics & RFIEC 60063 • IEC 60115

Series & Parallel Resistor Calculator

Combine up to six resistors and see the equivalent resistance, currents, voltages and which part runs hottest.

Series: Req = R1 + R2 + …  •  Parallel: 1/Req = Σ(1/Rk)  •  P = I²R
Calculated Result
—

Step-by-step

  1. Enter valid values to begin.

Ideal resistors at DC or low frequency; no tolerance, temperature coefficient or lead inductance. Leave a field blank to leave that resistor out; an entered 0 is treated as a short. With a current source and several shorted branches the current is assumed to split equally between them (real wiring resistance would decide). Pairs mode groups used resistors in order; an odd last resistor sits alone in its branch. The 50% utilisation band is a common derating practice, not a standard; use the manufacturer power-versus-temperature derating curve for the real limit.

IEC 60063 • IEC 60115 • Resistor Networks

Series and Parallel Resistors: Where the Current and the Heat Actually Go

Core Engineering Principles

Series resistors share one current, so the voltage divides in proportion to resistance and the biggest resistor dissipates the most heat. Parallel resistors share one voltage, so the current divides in inverse proportion and the smallest resistor takes the largest current and the largest slice of power. It decides what burns. A common case: someone builds a 100 Ω dummy load from four 400 Ω parts in parallel and assumes each carries a quarter of the power. It does, but only because the values match. Swap in one 390 Ω part and it quietly runs hottest.

Parallel equivalent resistance is always smaller than the smallest branch, and a 0 Ω branch makes it exactly zero, which on a voltage source is a fault, not a calculation. Real parts also come in E-series preferred values (IEC 60063), so we use series-parallel pairs to hit a target the catalogue lacks and tolerance then stacks. Rating is per part, too. A network that needs 0.63 W in total still fails if one 1/4 W resistor takes 0.31 W of it.

Series: Req = R1 + R2 + …  •  Parallel: 1/Req = 1/R1 + 1/R2 + …
Two in parallel: Req = R1R2 / (R1 + R2)  •  Power: P = I²R = V²/R

NEC & Standard References

IEC 60063 defines the E-series preferred values (E6, E12, E24, E96 and so on) that fixed resistors are made in. IEC 60115-1 is the generic specification for fixed resistors for electronic equipment, covering rated power, rated temperature and the derating curve above it. Read the datasheet for the power-versus-ambient curve and maximum working voltage, because a high-value resistor can hit its voltage limit before its power limit.
Worked Example: Building a 229 Ω Load from Four Stock Parts
Given: R1 = 100 Ω and R2 = 220 Ω in series, R3 = 470 Ω and R4 = 330 Ω in series, the two branches in parallel, 12 V applied, 1/2 W parts.
1. Branch A = 100 + 220 = 320 Ω; branch B = 470 + 330 = 800 Ω.
2. Req = 320 × 800 / 1120 = 228.6 Ω.
3. IA = 12 / 320 = 37.5 mA and IB = 12 / 800 = 15 mA, so the total is 52.5 mA.
4. Power: R1 = 0.141 W, R2 = 0.309 W, R3 = 0.106 W, R4 = 0.074 W; the total is 0.63 W, which matches 12 V × 52.5 mA.
5. R2 runs at 62% of its 1/2 W rating, above our usual 50% derating target. We move R2 to a 1 W part, which brings it to 31%.
Safety & Installation Rules
  • Rating is per resistor, not per network. Check the hottest part, which is usually the largest value in a series branch.
  • Derate for heat. Rated power applies at a stated ambient, and on a crowded board the allowed dissipation falls well below the headline figure.
  • A shorted or open part changes the sharing. If one parallel branch opens, the survivors take more current than you designed for.
  • Watch the voltage rating. Each part must stay under its own maximum working voltage.
  • Pulse loads need a pulse rating. A part safe at average power can still fail on a short energy burst.

Equal Resistors in Series and Parallel

Equal resistors of 100 Ω each.
NumberSeriesParallel
2200 Ω50 Ω
3300 Ω33.33 Ω
4400 Ω25 Ω
5500 Ω20 Ω
101 kΩ10 Ω

Two-Resistor Parallel Table

The result is always lower than the smaller resistor, which is a quick check.

Two resistors in parallel: Req = R1R2 / (R1 + R2).
R1 \ R2100 Ω220 Ω470 Ω1 kΩ4.7 kΩ10 kΩ
100 Ω50 Ω68.8 Ω82.5 Ω90.9 Ω97.9 Ω99 Ω
220 Ω68.8 Ω110 Ω149.9 Ω180.3 Ω210.2 Ω215.3 Ω
470 Ω82.5 Ω149.9 Ω235 Ω319.7 Ω427.3 Ω448.9 Ω
1 kΩ90.9 Ω180.3 Ω319.7 Ω500 Ω824.6 Ω909.1 Ω
4.7 kΩ97.9 Ω210.2 Ω427.3 Ω824.6 Ω2.35 kΩ3.197 kΩ
10 kΩ99 Ω215.3 Ω448.9 Ω909.1 Ω3.197 kΩ5 kΩ

Sharing Current and Power

Each parallel resistor sees the full voltage, so the smaller value takes more current and dissipates more power.

Current and power when 100 Ω and 220 Ω are in parallel across 12 V.
ResistorCurrentPower
100 Ω120.0 mA1440 mW
220 Ω54.5 mA655 mW
Total (parallel)174.5 mA2095 mW

Worked Example: Making 2.5 kΩ

No E12 resistor equals 2.5 kΩ. The pair 3.3 kΩ in parallel with 10 kΩ gives 2481 Ω, within 0.8%. In series, 1 kΩ + 1.5 kΩ gives exactly 2.5 kΩ with just two standard values. Check tolerance, since it stacks.

Series and Parallel Resistor Questions

How do I calculate resistors in series?

Add them: Req = R1 + R2 + …

How do I calculate resistors in parallel?

1/Req = 1/R1 + 1/R2 + …. For two resistors use R1R2 / (R1 + R2).

Why is parallel resistance less than the smallest resistor?

Adding another path for current always lowers the total resistance.

How is power shared in a series string?

The same current flows through all, so each dissipates I²R. The largest resistor runs hottest.

What if one resistor in a parallel network opens?

The total resistance rises and the remaining branches carry more current if the voltage is fixed.

Does tolerance matter?

Yes. Tolerances stack in series and parallel, so the result can be off by more than one resistor’s tolerance.