← Back to ElectroLab
Industrial & 3-PhaseNEC 430.122 / NEMA MG-1 Part 31

VFD Cable Sizing Calculator

Enter the motor current, cable length, rise time and carrier frequency to size the cable and check reflected-wave stress.

Icond ≥ 1.25 × FLC  •  Lcrit = tr × v / 2  •  Vpk ≈ Vdc (1 + Γ)
Calculated Result
—

Step-by-step

  1. Enter valid values to begin.

Ampacity: 125% of motor FLC (NEC 430.122(A)) from Table 310.16, then a conservative allowance for carrier-frequency heating (not an NEC factor). Reflected-wave estimate: critical length = tr × 150 m/µs / 2, peak = Vdc(1 + 0.9 × min(1, L/Lcrit)). The drive manufacturer’s maximum cable length and filter guidance always override these estimates.

NEC 430.122 • NEMA MG-1 Part 31 • IEEE 518 • VFD Cable

VFD Cable Sizing: Why Drive Cable Is Not Just Motor Cable

Core Engineering Principles

A variable-frequency drive doesn’t send a sine wave to the motor. It sends a train of fast voltage pulses, with rise times of 50 to 200 ns on modern IGBTs, switching at a carrier frequency of 2 to 16 kHz. Each pulse travels down the cable at about half the speed of light. When it reaches the motor, the motor’s surge impedance is much higher than the cable’s, so most of the pulse reflects back. If the cable is longer than the critical length, the reflected wave arrives at the motor terminals before the rise is complete and the voltage doubles. A 480 V drive has a 680 V DC bus, so you can see 1,300 V or more on a motor wound for 1,000 V peaks.

Those spikes puncture winding insulation, usually at the first turns of the first coil, and show up as repeated motor failures a year or two after commissioning. Current also looks different: the harmonic content and the high-frequency common-mode currents mean a cable runs warmer than its fundamental current suggests, and the common-mode current flows through bearings, which is why shaft-grounding rings and symmetrical three-ground cable have become standard on larger drives.

Conductor ≥ 125% × motor FLC (NEC 430.122)  •  Lcrit ≈ tr × v / 2, v ≈ 150 m/µs
Vpeak ≈ Vdc × (1 + Γ), Vdc = 1.414 × VLL, Γ ≤ 1

NEC & Standard References

NEC 430.122(A) says conductors supplying power conversion equipment must be rated at least 125% of the rated input current to the drive, and 430.131 covers the disconnecting means. NEMA MG-1 Part 31 defines inverter-duty motors rated for 1,600 V peak voltage and rise time of 0.1 µs or longer, and Part 30 covers general-purpose motors rated for only 1,000 V peak. IEEE 518 and IEEE 1566 cover noise and drive performance, and NEC 250.122 and the manufacturer’s EMC guide determine the grounding conductor. Use VFD-rated, XLPE-insulated, shielded cable with three symmetrical ground conductors and a 1,000 V rating for 480 V drives, and keep the drive-to-motor cable separate from control wiring.
Worked Example: 50 HP, 480 V Pump Drive, 150 ft Run, 4 kHz Carrier
Given: 65 A motor FLC, 150 ft (45.7 m), 480 V, IGBT rise time 100 ns, 4 kHz carrier, general-purpose motor (1,000 V limit).
1. Conductor: 65 × 1.25 = 81.3 A. With a 0.95 carrier-heating allowance, required ampacity = 81.3 / 0.95 = 85.5 A → 3 AWG copper at 75°C (100 A).
2. Critical length = 100 ns × 150 m/µs / 2 = 7.5 m. The run is 45.7 m, well beyond it, so full reflection.
3. Vdc = 1.414 × 480 = 679 V; Vpeak ≈ 679 × 1.9 = 1,290 V, above the 1,000 V general-purpose limit and below the 1,600 V inverter-duty limit.
4. Use an inverter-duty motor, or install a dv/dt filter at the drive.
Safety & Installation Rules
  • Shield and ground the right way. Terminate the shield 360° at both ends. A pigtail ground defeats the shield at the frequencies that matter.
  • Don’t put drive and control cable in the same tray. Separate by at least 12 in. or cross at 90°.
  • Bearing currents are real. Fluting on a bearing race is the telltale sign. Use a shaft grounding ring and an insulated bearing on large motors.
  • Don’t over-extend the cable. Check the drive manual for the maximum motor-cable length at your carrier frequency.

Conductor Size for Common Motors

Copper conductor for 460 V motors (NEC FLC), 125% and a 0.95 carrier-heating allowance, 75 °C column.
MotorFLCRequired ampacityWire
10 HP14 A18.4 A14 AWG
15 HP21 A27.6 A10 AWG
20 HP27 A35.5 A8 AWG
25 HP34 A44.7 A8 AWG
30 HP40 A52.6 A6 AWG
40 HP52 A68.4 A4 AWG
50 HP65 A85.5 A3 AWG
60 HP77 A101.3 A2 AWG
75 HP96 A126.3 A1 AWG
100 HP124 A163.2 A2/0 AWG

When Does Cable Length Matter?

Critical cable length for reflected wave: L = tr × 150 / 2 (m).
Rise timeCritical length
50 ns3.8 m
100 ns7.5 m
200 ns15.0 m
500 ns37.5 m

Peak Voltage at the Motor

General-purpose motors are typically rated about 1,000 V peak, inverter-duty about 1,600 V.

Estimated peak motor voltage on long cables (Vdc × 1.9).
Line voltageVdcVpeak
230 V325 V617 V
400 V565 V1074 V
480 V678 V1289 V
600 V848 V1611 V

Worked Example: 25 HP, 480 V, 100 m Run

FLC is 34 A, so 34 × 1.25 / 0.95 = 44.7 A, which needs 8 AWG at 75 °C (50 A). The critical length at 100 ns is 7.5 m, so a 100 m cable reflects fully. Peak voltage is about 1.414 × 480 × 1.9 = 1,290 V, above a general-purpose rating. Use an inverter-duty motor or a dv/dt filter, and shielded VFD cable.

VFD Cable Questions

How do I size a VFD cable?

125% of motor FLC, plus an allowance for carrier-frequency heating, then check voltage drop and reflected waves.

Why does cable length matter?

Beyond the critical length, voltage reflections can double the peak at the motor terminals.

What is a dv/dt filter?

A filter at the drive output that slows voltage edges to protect the motor insulation.

Do I need shielded cable?

Usually yes, to control noise and bearing currents.

Is an inverter-duty motor required?

Recommended for long cables and 480 V and above.

What carrier frequency should I use?

Lower carriers reduce heating and reflections but increase audible noise.