← Back to ElectroLab
NEC & Cable SizingNEC Ch. 9 Tables 1, 4, 5

Conduit Fill Calculator

Add up to three conductor groups, choose the conduit and see the fill percentage, PASS/FAIL result and the smallest compliant trade size.

Fill % = Σ(n × Awire) / Aconduit × 100  •  40% for 3+ wires
Calculated Result
—

Step-by-step

  1. Enter valid values to begin.

Conduit areas are from NEC Chapter 9 Table 4 and conductor areas from Table 5 (typed from the tables; verify against the NEC edition adopted in your area). Fill limits per Chapter 9 Table 1: 53% (1 conductor), 31% (2 conductors), 40% (3 or more).

NEC Chapter 9 • Tables 1, 4 & 5 • Conduit Fill

Conduit Fill: How Many Wires Actually Fit

Core Engineering Principles

Conduit isn’t sized like a bucket. Round wires don’t pack tightly, so a conduit that’s 100% “full” by area would be unpullable. Heat is the second problem. Wires in a crowded raceway can’t shed heat, so the conductors run hotter than the table assumed. The NEC handles both with a simple area limit. Add up the cross-sectional area of every conductor, divide by the internal area of the conduit, and keep the answer under the fill limit.

The limit depends on the count. One wire can fill 53%. Two wires get only 31% because two round cables sit side by side and jam the pull. Three or more get 40%. Insulation matters too. A 12 AWG THHN is thinner than a 12 AWG XHHW, so it takes up less room. Count everything, including the equipment ground and the neutral.

Fill = Σ(n × Awire) / Aconduit × 100  •  Limits: 1 wire 53%, 2 wires 31%, 3 or more 40%
Max count = floor(Aconduit × limit / Awire)

NEC & Standard References

The rules live in Chapter 9, Table 1 (the percentages), Table 4 (internal area by conduit type and trade size) and Table 5 (conductor areas). Note 1 points you to Annex C for same-size, same-type conductors, Note 3 says equipment grounding conductors count toward fill, Note 4 allows a nipple 24 in. or shorter to be filled to 60%, and Note 7 lets you round up when a count of identical conductors calculates to 0.8 or higher. EMT, PVC Schedule 40 and rigid have different internal diameters, so the same trade size holds different amounts of wire. PVC Schedule 80 is smaller still.

Worked Example: Three 12 AWG THHN in 3/4 in EMT
Given: 3 × 12 AWG THHN in 3/4 in EMT.
1. Table 5: 12 AWG THHN = 0.0133 in², so 3 × 0.0133 = 0.0399 in².
2. Table 4: 3/4 in EMT = 0.533 in²; 40% = 0.2132 in².
3. Fill = 0.0399 / 0.533 = 7.5%, well below the limit.
4. Maximum count = 0.2132 / 0.0133 = 16 conductors, but you wouldn’t run that many current-carrying conductors without derating.
Safety & Installation Rules
  • Fill is not derating. Sixteen wires might legally fit, but with more than three current-carrying conductors you also lose ampacity under 310.15(C)(1).
  • Bends matter more than percent. No more than 360° of bends between pull points. A legal fill with four 90s will still be a bad day for whoever pulls it.
  • Different insulation, different area. Use the actual insulation type on the job, not whatever was easiest to type.
  • Plan for the next circuit. If you’re over 30% fill, go one trade size up. Conduit is cheap and rework isn’t.

How Many Wires Fit in EMT Conduit?

This table shows the most THHN/THWN-2 conductors of one size that fit in EMT at the 40% limit for three or more wires, using the same NEC Table 4 and Table 5 areas as the calculator. Counts follow Chapter 9 Note 7 (a result of 0.8 or higher is rounded up). Remember that the ground counts too, and that the table does not cover derating.

THHN wire1/2 in3/4 in1 in1-1/4 in1-1/2 in2 in
14 AWG1222356184138
12 AWG916264561101
10 AWG51016283863
8 AWG369162236
6 AWG247121626
4 AWG12471016
2 AWG1235711
1/0 AWG012347
4/0 AWG001224

Check these counts against NEC Annex C and the code edition your inspector uses. Mixed wire sizes need the full calculation above.

EMT vs PVC vs Rigid: 12 AWG THHN Count

The same trade size holds a different number of wires depending on the conduit type, because the internal diameter changes. Maximum 12 AWG THHN conductors at 40% fill:

Trade sizeEMTPVC Sch. 40Rigid (RMC)
1/2 in989
3/4 in161516
1 in262526
1-1/4 in454346
1-1/2 in615962
2 in10199102
Worked Example: Five 10 AWG THHN in 1/2 in or 3/4 in EMT
Given: four 10 AWG THHN circuit conductors plus one 10 AWG THHN ground, so 5 wires.
1. Table 5: 10 AWG THHN = 0.0211 in², so 5 × 0.0211 = 0.1055 in².
2. 1/2 in EMT: 0.304 in² × 40% = 0.1216 in². Fill = 0.1055 / 0.304 = 34.7%, which passes but is tight.
3. 3/4 in EMT: fill = 0.1055 / 0.533 = 19.8%, which is much easier to pull.
Going up one trade size costs very little and saves a hard pull.

Conduit Fill and Ampacity Derating

Fitting the wires is only half the job. Under NEC 310.15(C)(1), when more than three current-carrying conductors share a raceway, the ampacity is adjusted: 4–6 conductors at 80%, 7–9 at 70%, 10–20 at 50%, 21–30 at 45%, 31–40 at 40%, and 41 or more at 35%. That is why a conduit that is legal for 16 wires is rarely used that way. Use the wire size calculator to pick the conductor, then check the raceway here.

Conduit Fill Questions

How many wires can fit in a 1/2 inch conduit?

With 12 AWG THHN in 1/2 in EMT, up to 9 conductors fit at the 40% limit (the table above has other sizes). Fewer is better in practice, and with more than three current-carrying conductors you must derate the ampacity.

How many 12 AWG wires fit in 3/4 inch EMT?

Sixteen 12 AWG THHN conductors fit in 3/4 in EMT by area (0.533 in² × 40% / 0.0133 in²). Remember that the ground counts, and that more than three current-carrying wires reduce the ampacity under NEC 310.15(C)(1).

How many 8 AWG THHN wires fit in 3/4 inch EMT?

The area calculation gives 5.8, and NEC Chapter 9 Note 7 lets you round a result of 0.8 or more up, so the answer is 6 conductors. Always count the equipment grounding conductor as one of them.

Why is the fill limit 31% for two wires?

Two round conductors in a round raceway tend to wedge against each other and the wall during a pull, so the NEC allows only 31%. A single conductor gets 53%, and three or more get 40%.

Do ground wires count toward conduit fill?

Yes. Equipment grounding conductors and bonding jumpers count in the fill calculation. Use their real insulated size, or the bare area from Table 8 if the conductor is bare.

Is the fill the same for EMT, PVC and rigid conduit?

No. The same trade size has a different internal area for each type, and PVC Schedule 40 is a little smaller than EMT in most sizes. Choose the right conduit type in the calculator above, because it changes the limit for a given trade size.

What is the 40% rule for conduit fill?

It is the NEC Chapter 9 Table 1 limit for three or more conductors: the total cross-section area of all wires must not exceed 40% of the conduit’s internal area. Nipples 24 in. or shorter may be filled to 60%.