← Back to ElectroLab
Industrial & 3-PhaseNEC 220.61 / IEEE 519

Three-Phase Neutral Current Calculator

Enter the three phase currents and the third-harmonic content to get neutral current and the minimum neutral conductor.

IN = √(Ia² + Ib² + Ic² − IaIb − IbIc − IcIa)  •  IN,3rd = Σ I3,phase
Calculated Result
—

Step-by-step

  1. Enter valid values to begin.

Fundamental currents are assumed 120° apart. Triplen harmonics (3rd, 9th, 15th) are in phase across the three conductors and add arithmetically in the neutral; only the third harmonic is modelled here. Use a true-RMS power-quality meter to measure real harmonic content. Ampacity from NEC Table 310.16.

NEC 220.61 • 310.15(E) • IEEE 519 • Neutral Current

Three-Phase Neutral Current: Unbalance and the Harmonic Surprise

Core Engineering Principles

In a balanced three-phase four-wire wye system, the three phase currents are equal and 120° apart, so they add to zero at the neutral. The neutral does nothing, and in a perfectly linear plant it could be the size of a pencil. In a real panel the phases are never equal, and what comes back down the neutral is the vector difference. The formula is IN = √(Ia² + Ib² + Ic² − IaIb − IbIc − IcIa). With 100, 90 and 80 A on the phases, the neutral carries only 17 A.

Then somebody installs switch-mode power supplies, LED drivers and drives, and the picture changes. These loads draw current in short pulses, which are rich in odd harmonics. The triplen harmonics, 3rd, 9th and 15th, are all in phase with each other in all three conductors. They don’t cancel in the neutral, they add. Three phases each carrying 35% third-harmonic put 105% of one phase’s current into the neutral, arithmetically. That’s how a neutral ends up with more current than any phase, in a panel that looks half loaded.

IN = √(Ia² + Ib² + Ic² − IaIb − IbIc − IcIa)  •  Triplens: IN,3rd = I3a + I3b + I3c
Total IN = √(IN,fund² + IN,3rd²)

NEC & Standard References

NEC 220.61(A) says the feeder or service neutral load is the maximum net computed load between the neutral and any one ungrounded conductor. 220.61(B) allows a demand reduction of 70% for the part over 200 A, but 220.61(C)(2) says no reduction for the portion of the load made up of nonlinear loads in a 4-wire wye system. NEC 310.15(E) says that on a 3-phase 4-wire wye system where the major part of the load is nonlinear, the neutral is counted as a current-carrying conductor for derating. IEEE 519 limits current distortion at the point of common coupling, and IEEE C57.110 covers transformer derating for harmonics. 4-wire delta systems have their own rules: the high-leg neutral is not the same as a wye neutral.
Worked Example: Office Panel with Computers and LED Lighting
Given: Phase currents 100 A, 90 A, 80 A (fundamental) with 35% third-harmonic content in each phase.
1. Fundamental neutral: √(100² + 90² + 80² − 100×90 − 90×80 − 80×100) = √300 = 17.3 A.
2. Third-harmonic per phase: 0.35 × (100, 90, 80) = 35, 31.5, 28 A; they add in the neutral: 94.5 A.
3. Total neutral: √(17.3² + 94.5²) = 96.1 A, which is 107% of the 90 A average phase current.
4. A 3 AWG copper neutral (100 A at 75°C) is the minimum; most engineers would pull a full-size neutral or a 200% neutral on an IT panel feeder.
Safety & Installation Rules
  • Clamp-on meters lie. An average-reading meter underestimates harmonic current. Use a true-RMS meter and check the neutral separately.
  • Neutral overheating is silent. Breakers don’t protect a neutral, so a burned neutral shows up as insulation damage or a failed lug.
  • Shared neutrals are risky. Multi-wire branch circuits with nonlinear loads can overload the shared neutral.
  • Transformers pay too. The third-harmonic current circulates in a delta primary and heats the winding. Use K-rated transformers when nonlinear loads exceed about 30%.
  • Loose neutral = overvoltage. If the neutral opens, single-phase loads can see 208 V instead of 120 V.

Unbalance in Linear Loads

Neutral current of linear loads from phase unbalance.
Phase currentsNeutral current% of largest phase
100 / 100 / 100 A0.0 A0%
100 / 90 / 80 A17.3 A17%
100 / 100 / 50 A50.0 A50%
100 / 50 / 0 A86.6 A87%
100 / 0 / 0 A100.0 A100%

Third Harmonics

Three phases at 100 A each, balanced, with third-harmonic content. Triplens add in the neutral.
3rd harmonicNeutral current% of phase
0%0 A0%
15%45 A45%
33%99 A99%
50%150 A150%
70%210 A210%

Neutral Sizing

Neutral sizing guide.
LoadNeutral
Linear, balanced or modest unbalance100% of phase
Mixed office loads100 to 150%
Mostly electronic loads173 to 200%

Worked Example: Panel with 120 / 110 / 100 A and 40% Third Harmonic

Fundamental neutral = √(120² + 110² + 100² − 120×110 − 110×100 − 100×120) = 17.3 A. Third harmonic: 0.40 × 330 = 132 A, adding arithmetically. Total neutral = √(17.3² + 132²) = 133.1 A, which is 121% of the 110 A average phase current. A full-size neutral is the minimum; a 200% neutral is better.

Neutral Current Questions

Why can the neutral carry more current than the phases?

Triplen harmonics (3rd, 9th, 15th) are in phase in all three conductors and add in the neutral.

How do I calculate neutral current from unbalance?

IN = √(Ia² + Ib² + Ic² − IaIb − IbIc − IcIa).

Is the neutral a current-carrying conductor?

For nonlinear loads such as computers and LED drivers, yes, and it counts for derating.

What size neutral for electronic loads?

Full-size or up to 200%, and consider a K-rated transformer.

How can I reduce neutral current?

Balance loads, use zig-zag filters or fit a transformer with a delta primary.

Does the NEC require a larger neutral?

No, but harmonic loading can overheat a full-size one. Follow the adopted edition.