← Back to ElectroLab
Electronics & RFIEC 60063 • Thevenin / Ohm’s Law

Voltage Divider Calculator

Enter Vin, R1, R2 and an optional load to get the loaded output, Thevenin equivalent and power.

Vout = Vin × R2 / (R1 + R2)  •  Rth = R1‖R2
Calculated Result
—

Step-by-step

  1. Enter valid values to begin.

Ideal source and ideal resistors assumed: no tolerance, temperature coefficient or source impedance. The load RL sits in parallel with R2. In Solve mode R2 is calculated so the loaded Vout (including RL if entered) equals the target, then rounded to the chosen series; the R2 and mode-irrelevant fields are ignored. The 0.125 W check assumes 1/4 W resistors at 50% derating, which is practice, not a standard.

IEC 60063 • IEC 60115-1 • IEEE Std 100 • Thevenin / Ohm’s Law

Voltage Divider: Why the Load Changes Your Answer

Core Engineering Principles

A divider of two resistors gives Vout = Vin × R2 / (R1 + R2), and every textbook stops there. The catch is that the formula assumes nothing is connected to the output. The moment you attach a load, that load sits in parallel with R2, the lower leg gets smaller, and the output sags. The cleanest way to think about it is through Thevenin: seen from the output, the divider is a source of Vth = Vin × R2/(R1 + R2) with a series resistance Rth = R1 ‖ R2. Any load draws current through that Rth, so the output drops by exactly that amount.

From that picture the rule falls out. If the load is at least ten times Rth, the output falls by roughly 10% or less, and a hundred times keeps you near 1%. The cure is low resistances, but low resistances burn power all the time. On a battery product we choose the highest values the load impedance and the noise floor allow, and we buffer the tap with an op-amp when the load is unknown.

Vout = Vin × R2 / (R1 + R2)  •  Loaded: R2′ = R2 ‖ RL
Rth = R1 ‖ R2  •  Solve: R2 = R1 × Vout / (Vin − Vout)

NEC & Standard References

IEC 60063 sets the E12, E24 and E96 preferred values you pick R2 from. IEC 60115-1 is the generic specification for fixed resistors; it covers rated power, tolerance, temperature coefficient and the derating curve, all of which move your ratio. IEEE Std 100 gives the formal definitions of the terms used here, such as Thevenin equivalent circuit and source impedance. The 10× load rule and 50% power derating are practice, not standards.
Worked Example: 12 V Rail Down to About 3 V for a Sensor
Given: Vin = 12 V, R1 = 10 kΩ, R2 = 3.3 kΩ, load RL = 100 kΩ.
1. Unloaded Vout = 12 × 3.3 / 13.3 = 2.977 V (ratio 0.2481).
2. R2 ‖ RL = 3.3 × 100 / 103.3 = 3.195 kΩ, so loaded Vout = 12 × 3.195 / 13.195 = 2.905 V, which is −2.42%.
3. Rth = 10 ‖ 3.3 = 2.481 kΩ; ten times is 24.8 kΩ, and the 100 kΩ load clears it.
4. Divider current = 12 / 13.195 kΩ = 0.9095 mA. PR1 = 8.27 mW, PR2 = 2.56 mW, total = 10.9 mW.
5. To get exactly 5 V from the same R1 with no load, R2 = 10 k × 5 / 7 = 7.143 kΩ. E24 gives 7.5 kΩ (5.14 V); E96 gives 7.15 kΩ (5.003 V).
Safety & Installation Rules
  • Don’t use a divider as a power supply. It has no regulation and a high output impedance; any real current drags it down. Use a regulator.
  • Check the high-voltage case. Mains-sense and battery-monitor dividers must handle the full rail across R1, with resistor voltage ratings and creepage respected. Use several resistors in series for hundreds of volts.
  • Input leakage matters at high impedance. A nanoamp of op-amp bias current through 1 MΩ is a millivolt of error.
  • Protect the tap. If R1 shorts, the full Vin arrives at a pin rated for a few volts; add a clamp diode or Zener.

Common Voltage Divider Values

Starting points for frequently needed ratios. R2 is picked from the E24 series, so the real output is close to the target but not exact. For a closer match use E96 values in the calculator above.

Divider design with an E24 R2 (no load). R2 exact = R1 × Vout / (Vin − Vout)
VinTarget VoutR1R2 exactR2 (E24)Actual Vout
12 V5 V10 kΩ7.14286 kΩ7.5 kΩ5.143 V
12 V3.3 V10 kΩ3.7931 kΩ3.9 kΩ3.367 V
5 V3.3 V10 kΩ19.4118 kΩ20 kΩ3.333 V
24 V5 V10 kΩ2.63158 kΩ2.7 kΩ5.102 V
24 V12 V10 kΩ10 kΩ10 kΩ12.000 V
9 V3.3 V10 kΩ5.78947 kΩ5.6 kΩ3.231 V
3.3 V1.8 V10 kΩ12 kΩ12 kΩ1.800 V
48 V5 V47 kΩ5.46512 kΩ5.6 kΩ5.110 V

How Much Does a Load Change the Output?

A load in parallel with R2 pulls the output down. The table shows the effect for a 12 V divider with two equal 10 kΩ resistors, with the load expressed as a multiple of the Thevenin resistance Rth = R1 ‖ R2.

Loading error for a 12 V divider with R1 = R2 = 10 kΩ (Rth = 5 kΩ, unloaded 6.000 V)
Load resistanceLoaded VoutError
1 × Rth (5.0 kΩ)3.000 V-50.0%
3 × Rth (15.0 kΩ)4.500 V-25.0%
10 × Rth (50.0 kΩ)5.455 V-9.1%
30 × Rth (150.0 kΩ)5.806 V-3.2%
100 × Rth (500.0 kΩ)5.941 V-1.0%

A load ten times Rth costs about 9% here, and a hundred times costs about 1%. If your load is lower than that, use smaller resistors or buffer the tap with an op-amp.

Voltage Divider for a 12 V to 5 V Level

Use R1 = 10 kΩ. Then R2 = 10 k × 5 / 7 = 7.14 kΩ. With the nearest E24 value of 7.5 kΩ you get 12 × 7.5 / 17.5 = 5.14 V. Use a regulator if the 5 V rail must supply real current, since a divider has a high output resistance.

Divider Current and Power

Current through the divider is Vin / (R1 + R2). For 12 V across 10 kΩ and 7.5 kΩ that is 0.69 mA and 8.2 mW. Smaller resistors give stiffer outputs but waste more power, which matters on battery-powered designs.

Voltage Divider Questions

How do I calculate a voltage divider?

Vout = Vin × R2 / (R1 + R2). To find R2 for a target output, use R2 = R1 × Vout / (Vin − Vout), then choose the closest standard value.

What resistors do I need to divide 12 V down to 5 V?

With R1 = 10 kΩ, R2 = 7.14 kΩ. The nearest E24 value is 7.5 kΩ (5.14 V), and E96 gives 7.15 kΩ (about 5.003 V).

Can I use a voltage divider to power a device?

Not safely. A divider has no regulation and a high output resistance, so the output voltage falls as the device draws current. Use a regulator or a buck converter for power.

Why is my measured divider voltage lower than the formula?

Something is loading the output, such as a multimeter or microcontroller input, which acts in parallel with R2. Include the load resistance in the calculator to see the loaded value.

What resistor values should I choose for a divider?

Pick values that are low enough that the load and input leakage do not disturb the ratio (the load should be at least ten times Rth), but high enough to keep the current and power small. 10 kΩ to 100 kΩ suits many logic and sensor circuits.

Can a voltage divider step a voltage up?

No. A resistive divider only reduces the voltage, and the output is always lower than the input. A boost converter or amplifier is needed to increase it.